9C53E68A8730997FEF7D414 +lah8\Ȯ1h d?_I|+>/* * include/linux/serial_reg.h * * Copyright (C) 1992, 1994 by Theodore Ts'o. * * Redistribution of this file is permitted under the terms of the GNU * Public License (GPL) * * These are the UART port assignments, expressed as offsets from the base * register. These assignments should hold for any serial port based on * a 8250, 16450, or 16550(A). */ #ifndef _LINUX_SERIAL_REG_H #define _LINUX_SERIAL_REG_H /* * DLAB=0 */ #define UART_RX 0 /* In: Receive buffer */ #define UART_TX 0 /* Out: Transmit buffer */ #define UART_IER 1 /* Out: Interrupt Enable Register */ #define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ #define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ #define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ #define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ /* * Sleep mode for ST16650 and TI16750. For the ST16650, EFR[4]=1 */ #define UART_IERX_SLEEP 0x10 /* Enable sleep mode */ #define UART_IIR 2 /* In: Interrupt ID Register */ #define UART_IIR_NO_INT 0x01 /* No interrupts pending */ #define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ #define UART_IIR_MSI 0x00 /* Modem status interrupt */ #define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ #define UART_IIR_RDI 0x04 /* Receiver data interrupt */ #define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ #define UART_IIR_BUSY 0x07 /* DesignWare APB Busy Detect */ #define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */ #define UART_IIR_XOFF 0x10 /* OMAP XOFF/Special Character */ #define UART_IIR_CTS_RTS_DSR 0x20 /* OMAP CTS/RTS/DSR Change */ #define UART_FCR 2 /* Out: FIFO Control Register */ #define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ #define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ #define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ #define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ /* * Note: The FIFO trigger levels are chip specific: * RX:76 = 00 01 10 11 TX:54 = 00 01 10 11 * PC16550D: 1 4 8 14 xx xx xx xx * TI16C550A: 1 4 8 14 xx xx xx xx * TI16C550C: 1 4 8 14 xx xx xx xx * ST16C550: 1 4 8 14 xx xx xx xx * ST16C650: 8 16 24 28 16 8 24 30 PORT_16650V2 * NS16C552: 1 4 8 14 xx xx xx xx * ST16C654: 8 16 56 60 8 16 32 56 PORT_16654 * TI16C750: 1 16 32 56 xx xx xx xx PORT_16750 * TI16C752: 8 16 56 60 8 16 32 56 * Tegra: 1 4 8 14 16 8 4 1 PORT_TEGRA */ #define UART_FCR_R_TRIG_00 0x00 #define UART_FCR_R_TRIG_01 0x40 #define UART_FCR_R_TRIG_10 0x80 #define UART_FCR_R_TRIG_11 0xc0 #define UART_FCR_T_TRIG_00 0x00 #define UART_FCR_T_TRIG_01 0x10 #define UART_FCR_T_TRIG_10 0x20 #define UART_FCR_T_TRIG_11 0x30 #define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */ #define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */ #define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */ #define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */ #define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */ /* 16650 definitions */ #define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */ #define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */ #define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */ #define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */ #define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */ #define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */ #define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */ #define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */ #define UART_FCR7_64BYTE 0x20 /* Go into 64 byte mode (TI16C750) */ #define UART_LCR 3 /* Out: Line Control Register */ /* * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting * UART_LCR_STOP will select 1